2017-06-16 05:38:15 +02:00
|
|
|
|
# For more options and information see
|
|
|
|
|
|
# http://www.raspberrypi.org/documentation/configuration/config-txt.md
|
|
|
|
|
|
# Some settings may impact device functionality. See link above for details
|
|
|
|
|
|
|
|
|
|
|
|
# uncomment if you get no picture on HDMI for a default "safe" mode
|
|
|
|
|
|
#hdmi_safe=1
|
|
|
|
|
|
|
|
|
|
|
|
# uncomment this if your display has a black border of unused pixels visible
|
|
|
|
|
|
# and your display can output without overscan
|
|
|
|
|
|
#disable_overscan=1
|
|
|
|
|
|
|
|
|
|
|
|
# uncomment the following to adjust overscan. Use positive numbers if console
|
|
|
|
|
|
# goes off screen, and negative if there is too much border
|
|
|
|
|
|
#overscan_left=16
|
|
|
|
|
|
#overscan_right=16
|
|
|
|
|
|
#overscan_top=16
|
|
|
|
|
|
#overscan_bottom=16
|
|
|
|
|
|
|
|
|
|
|
|
# uncomment to force a console size. By default it will be display's size minus
|
|
|
|
|
|
# overscan.
|
|
|
|
|
|
#framebuffer_width=1280
|
|
|
|
|
|
#framebuffer_height=720
|
|
|
|
|
|
|
|
|
|
|
|
# uncomment if hdmi display is not detected and composite is being output
|
|
|
|
|
|
hdmi_force_hotplug=1
|
|
|
|
|
|
|
|
|
|
|
|
# uncomment to force a specific HDMI mode (this will force VGA)
|
|
|
|
|
|
#hdmi_group=1
|
|
|
|
|
|
#hdmi_mode=1
|
|
|
|
|
|
|
|
|
|
|
|
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
|
|
|
|
|
# DMT (computer monitor) modes
|
|
|
|
|
|
#hdmi_drive=2
|
|
|
|
|
|
|
|
|
|
|
|
# uncomment to increase signal to HDMI, if you have interference, blanking, or
|
|
|
|
|
|
# no display
|
|
|
|
|
|
#config_hdmi_boost=4
|
|
|
|
|
|
|
|
|
|
|
|
# uncomment for composite PAL
|
|
|
|
|
|
#sdtv_mode=2
|
|
|
|
|
|
|
|
|
|
|
|
#uncomment to overclock the arm. 700 MHz is the default.
|
|
|
|
|
|
#arm_freq=800
|
|
|
|
|
|
|
|
|
|
|
|
# Uncomment some or all of these to enable the optional hardware interfaces
|
|
|
|
|
|
dtparam=i2c_arm=on
|
|
|
|
|
|
#dtparam=i2s=on
|
|
|
|
|
|
dtparam=spi=on
|
|
|
|
|
|
enable_uart=1
|
|
|
|
|
|
# Uncomment this to enable the lirc-rpi module
|
|
|
|
|
|
#dtoverlay=lirc-rpi
|
|
|
|
|
|
|
|
|
|
|
|
# Additional overlays and parameters are documented /boot/overlays/README
|
|
|
|
|
|
|
|
|
|
|
|
# Enable audio (loads snd_bcm2835)
|
|
|
|
|
|
dtparam=audio=on
|
|
|
|
|
|
|
|
|
|
|
|
display_rotate=1
|
2017-10-18 15:14:00 +02:00
|
|
|
|
dtoverlay=qddpi24
|
2017-06-16 05:38:15 +02:00
|
|
|
|
overscan_left=0
|
|
|
|
|
|
overscan_right=0
|
|
|
|
|
|
overscan_top=0
|
|
|
|
|
|
overscan_bottom=0
|
|
|
|
|
|
framebuffer_width=480
|
|
|
|
|
|
framebuffer_height=320
|
|
|
|
|
|
enable_dpi_lcd=1
|
|
|
|
|
|
display_default_lcd=1
|
|
|
|
|
|
dpi_group=2
|
|
|
|
|
|
dpi_mode=87
|
2017-10-18 15:14:00 +02:00
|
|
|
|
dpi_output_format=0x07f003
|
|
|
|
|
|
hdmi_timings=321 0 28 18 28 480 0 2 2 4 0 0 0 60 0 32000000 6
|
2017-06-16 05:38:15 +02:00
|
|
|
|
|
2017-10-18 15:14:00 +02:00
|
|
|
|
dtoverlay=ads7846,cs=1,penirq=18,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900
|
