lcd driver
lcd driver
This commit is contained in:
goodtft
parent
a810278dcd
commit
cf3bc68bd8
34 changed files with 794 additions and 0 deletions
6
LCD-hdmi
Normal file
6
LCD-hdmi
Normal file
|
|
@ -0,0 +1,6 @@
|
||||||
|
sudo cp -rf ./usr/modules-HDMI /etc/modules
|
||||||
|
sudo cp -rf ./usr/99-fbturbo.conf-HDMI /usr/share/X11/xorg.conf.d/99-fbturbo.conf
|
||||||
|
sudo cp ./boot/config-nomal.txt /boot/config.txt
|
||||||
|
sudo cp ./usr/cmdline.txt /boot/
|
||||||
|
sudo cp ./usr/inittab /etc/
|
||||||
|
sudo reboot
|
||||||
9
LCD28-show
Normal file
9
LCD28-show
Normal file
|
|
@ -0,0 +1,9 @@
|
||||||
|
sudo mkdir /etc/X11/xorg.conf.d
|
||||||
|
sudo cp ./usr/tft9341-overlay.dtb /boot/overlays/
|
||||||
|
sudo cp ./usr/tft9341-overlay.dtb /boot/overlays/tft9341.dtbo
|
||||||
|
sudo cp -rf ./usr/99-calibration.conf-28 /etc/X11/xorg.conf.d/99-calibration.conf
|
||||||
|
sudo cp -rf ./usr/99-fbturbo.conf /usr/share/X11/xorg.conf.d/
|
||||||
|
sudo cp ./usr/cmdline.txt /boot/
|
||||||
|
sudo cp ./usr/inittab /etc/
|
||||||
|
sudo cp ./boot/config-28.txt /boot/config.txt
|
||||||
|
sudo reboot
|
||||||
9
LCD32-show
Normal file
9
LCD32-show
Normal file
|
|
@ -0,0 +1,9 @@
|
||||||
|
sudo mkdir /etc/X11/xorg.conf.d
|
||||||
|
sudo cp ./usr/tft9341-overlay.dtb /boot/overlays/
|
||||||
|
sudo cp ./usr/tft9341-overlay.dtb /boot/overlays/tft9341.dtbo
|
||||||
|
sudo cp -rf ./usr/99-calibration.conf-32 /etc/X11/xorg.conf.d/99-calibration.conf
|
||||||
|
sudo cp -rf ./usr/99-fbturbo.conf /usr/share/X11/xorg.conf.d/
|
||||||
|
sudo cp ./usr/cmdline.txt /boot/
|
||||||
|
sudo cp ./usr/inittab /etc/
|
||||||
|
sudo cp ./boot/config-32.txt /boot/config.txt
|
||||||
|
sudo reboot
|
||||||
9
LCD35-show
Normal file
9
LCD35-show
Normal file
|
|
@ -0,0 +1,9 @@
|
||||||
|
sudo mkdir /etc/X11/xorg.conf.d
|
||||||
|
sudo cp ./usr/tft35a-overlay.dtb /boot/overlays/
|
||||||
|
sudo cp ./usr/tft35a-overlay.dtb /boot/overlays/tft35a.dtbo
|
||||||
|
sudo cp -rf ./usr/99-calibration.conf-35 /etc/X11/xorg.conf.d/99-calibration.conf
|
||||||
|
sudo cp -rf ./usr/99-fbturbo.conf /usr/share/X11/xorg.conf.d/
|
||||||
|
sudo cp ./usr/cmdline.txt /boot/
|
||||||
|
sudo cp ./usr/inittab /etc/
|
||||||
|
sudo cp ./boot/config-35.txt /boot/config.txt
|
||||||
|
sudo reboot
|
||||||
7
LCD397-show
Normal file
7
LCD397-show
Normal file
|
|
@ -0,0 +1,7 @@
|
||||||
|
sudo cp -rf ./boot/config-397.txt /boot/config.txt
|
||||||
|
sudo cp ./usr/cmdline.txt /boot/
|
||||||
|
sudo cp ./usr/inittab /etc/
|
||||||
|
sudo cp -rf ./usr/99-fbturbo.conf-HDMI /usr/share/X11/xorg.conf.d/99-fbturbo.conf
|
||||||
|
sudo mkdir /etc/X11/xorg.conf.d
|
||||||
|
sudo cp -rf ./usr/99-calibration.conf-397 /etc/X11/xorg.conf.d/99-calibration.conf
|
||||||
|
sudo reboot
|
||||||
7
LCD43-show
Normal file
7
LCD43-show
Normal file
|
|
@ -0,0 +1,7 @@
|
||||||
|
sudo cp -rf ./boot/config-43.txt /boot/config.txt
|
||||||
|
sudo cp ./usr/cmdline.txt /boot/
|
||||||
|
sudo cp ./usr/inittab /etc/
|
||||||
|
sudo cp -rf ./usr/99-fbturbo.conf-HDMI /usr/share/X11/xorg.conf.d/99-fbturbo.conf
|
||||||
|
sudo mkdir /etc/X11/xorg.conf.d
|
||||||
|
sudo cp -rf ./usr/99-calibration.conf-43 /etc/X11/xorg.conf.d/99-calibration.conf
|
||||||
|
sudo reboot
|
||||||
7
LCD5-show
Normal file
7
LCD5-show
Normal file
|
|
@ -0,0 +1,7 @@
|
||||||
|
sudo cp -rf ./boot/config-5.txt /boot/config.txt
|
||||||
|
sudo cp ./usr/cmdline.txt /boot/
|
||||||
|
sudo cp ./usr/inittab /etc/
|
||||||
|
sudo cp -rf ./usr/99-fbturbo.conf-HDMI /usr/share/X11/xorg.conf.d/99-fbturbo.conf
|
||||||
|
sudo mkdir /etc/X11/xorg.conf.d
|
||||||
|
sudo cp -rf ./usr/99-calibration.conf-5 /etc/X11/xorg.conf.d/99-calibration.conf
|
||||||
|
sudo reboot
|
||||||
5
LCD7B-show
Normal file
5
LCD7B-show
Normal file
|
|
@ -0,0 +1,5 @@
|
||||||
|
sudo cp -rf ./boot/config-7B-800x480.txt /boot/config.txt
|
||||||
|
sudo cp ./usr/cmdline.txt /boot/
|
||||||
|
sudo cp ./usr/inittab /etc/
|
||||||
|
sudo cp -rf ./usr/99-fbturbo.conf-HDMI /usr/share/X11/xorg.conf.d/99-fbturbo.conf
|
||||||
|
sudo reboot
|
||||||
5
LCD7C-show
Normal file
5
LCD7C-show
Normal file
|
|
@ -0,0 +1,5 @@
|
||||||
|
sudo cp -rf ./boot/config-7C-1024x600.txt /boot/config.txt
|
||||||
|
sudo cp ./usr/cmdline.txt /boot/
|
||||||
|
sudo cp ./usr/inittab /etc/
|
||||||
|
sudo cp -rf ./usr/99-fbturbo.conf-HDMI /usr/share/X11/xorg.conf.d/99-fbturbo.conf
|
||||||
|
sudo reboot
|
||||||
34
ReadMe.txt
Normal file
34
ReadMe.txt
Normal file
|
|
@ -0,0 +1,34 @@
|
||||||
|
|
||||||
|
[version]
|
||||||
|
v1.1
|
||||||
|
[Driver installation]
|
||||||
|
Step1, Install Raspbian official mirror
|
||||||
|
1)Download Raspbian official mirror:https://www.raspberrypi.org/downloads/
|
||||||
|
2)Use“SDFormatter.exe”to Format your TF Card，
|
||||||
|
3)Use“Win32DiskImager.exe” Burning mirror to TF Card。
|
||||||
|
Step2, Install LCD Driver
|
||||||
|
1)Copy “LCD-show-160701.tar.gz” to the root directory of raspberry pi（you can copy it directly to TF card after Step1, or use SFTP to remote copy）
|
||||||
|
2)Landing Raspberry pi system to user command line (Name:pi,Password:raspberry)，Execute the following command:
|
||||||
|
cd /boot
|
||||||
|
sudo tar zxvf LCD-show-160701.tar.gz
|
||||||
|
cd LCD-show/
|
||||||
|
#For 2.8inch RPI LCD excute:
|
||||||
|
sudo ./LCD28-show
|
||||||
|
# For 3.2inch RPI LCD excute:
|
||||||
|
sudo ./LCD32-show
|
||||||
|
# For 3.5inch RPI LCD excute:
|
||||||
|
sudo ./LCD35-show
|
||||||
|
# For 3.97inch RPI LCD excute:
|
||||||
|
sudo ./LCD397-show
|
||||||
|
# For 4.3inch RPI LCD excute:
|
||||||
|
sudo ./LCD43-show
|
||||||
|
# For 5inch RPI LCD excute:
|
||||||
|
sudo ./LCD5-show
|
||||||
|
# For 7inch(B)-800X480 RPI LCD excute:
|
||||||
|
sudo ./LCD7B-show
|
||||||
|
# For 7inch(C)-1024X600 RPI LCD excute:
|
||||||
|
sudo ./LCD7C-show
|
||||||
|
# If you need to switch back to the traditional HDMI display excute:
|
||||||
|
Sudo ./LCD-hdmi
|
||||||
|
|
||||||
|
3)Wait a few minutes,the system will restart automaticall , enjoy with your LCD.
|
||||||
58
boot/config-28.txt
Normal file
58
boot/config-28.txt
Normal file
|
|
@ -0,0 +1,58 @@
|
||||||
|
# For more options and information see
|
||||||
|
# http://www.raspberrypi.org/documentation/configuration/config-txt.md
|
||||||
|
# Some settings may impact device functionality. See link above for details
|
||||||
|
|
||||||
|
# uncomment if you get no picture on HDMI for a default "safe" mode
|
||||||
|
#hdmi_safe=1
|
||||||
|
|
||||||
|
# uncomment this if your display has a black border of unused pixels visible
|
||||||
|
# and your display can output without overscan
|
||||||
|
#disable_overscan=1
|
||||||
|
|
||||||
|
# uncomment the following to adjust overscan. Use positive numbers if console
|
||||||
|
# goes off screen, and negative if there is too much border
|
||||||
|
#overscan_left=16
|
||||||
|
#overscan_right=16
|
||||||
|
#overscan_top=16
|
||||||
|
#overscan_bottom=16
|
||||||
|
|
||||||
|
# uncomment to force a console size. By default it will be display's size minus
|
||||||
|
# overscan.
|
||||||
|
#framebuffer_width=1280
|
||||||
|
#framebuffer_height=720
|
||||||
|
|
||||||
|
# uncomment if hdmi display is not detected and composite is being output
|
||||||
|
hdmi_force_hotplug=1
|
||||||
|
|
||||||
|
# uncomment to force a specific HDMI mode (this will force VGA)
|
||||||
|
#hdmi_group=1
|
||||||
|
#hdmi_mode=1
|
||||||
|
|
||||||
|
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
||||||
|
# DMT (computer monitor) modes
|
||||||
|
#hdmi_drive=2
|
||||||
|
|
||||||
|
# uncomment to increase signal to HDMI, if you have interference, blanking, or
|
||||||
|
# no display
|
||||||
|
#config_hdmi_boost=4
|
||||||
|
|
||||||
|
# uncomment for composite PAL
|
||||||
|
#sdtv_mode=2
|
||||||
|
|
||||||
|
#uncomment to overclock the arm. 700 MHz is the default.
|
||||||
|
#arm_freq=800
|
||||||
|
|
||||||
|
# Uncomment some or all of these to enable the optional hardware interfaces
|
||||||
|
dtparam=i2c_arm=on
|
||||||
|
#dtparam=i2s=on
|
||||||
|
dtparam=spi=on
|
||||||
|
enable_uart=1
|
||||||
|
# Uncomment this to enable the lirc-rpi module
|
||||||
|
#dtoverlay=lirc-rpi
|
||||||
|
|
||||||
|
# Additional overlays and parameters are documented /boot/overlays/README
|
||||||
|
|
||||||
|
# Enable audio (loads snd_bcm2835)
|
||||||
|
dtparam=audio=on
|
||||||
|
dtoverlay=tft9341:rotate=90
|
||||||
|
dtoverlay=ads7846,cs=1,penirq=17,penirq_pull=2,speed=1000000,keep_vref_on=1,swapxy=0,pmax=255,xohms=60,xmin=200,xmax=3900,ymin=200,ymax=3900
|
||||||
58
boot/config-32.txt
Normal file
58
boot/config-32.txt
Normal file
|
|
@ -0,0 +1,58 @@
|
||||||
|
# For more options and information see
|
||||||
|
# http://www.raspberrypi.org/documentation/configuration/config-txt.md
|
||||||
|
# Some settings may impact device functionality. See link above for details
|
||||||
|
|
||||||
|
# uncomment if you get no picture on HDMI for a default "safe" mode
|
||||||
|
#hdmi_safe=1
|
||||||
|
|
||||||
|
# uncomment this if your display has a black border of unused pixels visible
|
||||||
|
# and your display can output without overscan
|
||||||
|
#disable_overscan=1
|
||||||
|
|
||||||
|
# uncomment the following to adjust overscan. Use positive numbers if console
|
||||||
|
# goes off screen, and negative if there is too much border
|
||||||
|
#overscan_left=16
|
||||||
|
#overscan_right=16
|
||||||
|
#overscan_top=16
|
||||||
|
#overscan_bottom=16
|
||||||
|
|
||||||
|
# uncomment to force a console size. By default it will be display's size minus
|
||||||
|
# overscan.
|
||||||
|
#framebuffer_width=1280
|
||||||
|
#framebuffer_height=720
|
||||||
|
|
||||||
|
# uncomment if hdmi display is not detected and composite is being output
|
||||||
|
hdmi_force_hotplug=1
|
||||||
|
|
||||||
|
# uncomment to force a specific HDMI mode (this will force VGA)
|
||||||
|
#hdmi_group=1
|
||||||
|
#hdmi_mode=1
|
||||||
|
|
||||||
|
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
||||||
|
# DMT (computer monitor) modes
|
||||||
|
#hdmi_drive=2
|
||||||
|
|
||||||
|
# uncomment to increase signal to HDMI, if you have interference, blanking, or
|
||||||
|
# no display
|
||||||
|
#config_hdmi_boost=4
|
||||||
|
|
||||||
|
# uncomment for composite PAL
|
||||||
|
#sdtv_mode=2
|
||||||
|
|
||||||
|
#uncomment to overclock the arm. 700 MHz is the default.
|
||||||
|
#arm_freq=800
|
||||||
|
|
||||||
|
# Uncomment some or all of these to enable the optional hardware interfaces
|
||||||
|
dtparam=i2c_arm=on
|
||||||
|
#dtparam=i2s=on
|
||||||
|
dtparam=spi=on
|
||||||
|
enable_uart=1
|
||||||
|
# Uncomment this to enable the lirc-rpi module
|
||||||
|
#dtoverlay=lirc-rpi
|
||||||
|
|
||||||
|
# Additional overlays and parameters are documented /boot/overlays/README
|
||||||
|
|
||||||
|
# Enable audio (loads snd_bcm2835)
|
||||||
|
dtparam=audio=on
|
||||||
|
dtoverlay=tft9341:rotate=270
|
||||||
|
dtoverlay=ads7846,cs=1,penirq=17,penirq_pull=2,speed=1000000,keep_vref_on=1,swapxy=0,pmax=255,xohms=60,xmin=200,xmax=3900,ymin=200,ymax=3900
|
||||||
58
boot/config-35.txt
Normal file
58
boot/config-35.txt
Normal file
|
|
@ -0,0 +1,58 @@
|
||||||
|
# For more options and information see
|
||||||
|
# http://www.raspberrypi.org/documentation/configuration/config-txt.md
|
||||||
|
# Some settings may impact device functionality. See link above for details
|
||||||
|
|
||||||
|
# uncomment if you get no picture on HDMI for a default "safe" mode
|
||||||
|
#hdmi_safe=1
|
||||||
|
|
||||||
|
# uncomment this if your display has a black border of unused pixels visible
|
||||||
|
# and your display can output without overscan
|
||||||
|
#disable_overscan=1
|
||||||
|
|
||||||
|
# uncomment the following to adjust overscan. Use positive numbers if console
|
||||||
|
# goes off screen, and negative if there is too much border
|
||||||
|
#overscan_left=16
|
||||||
|
#overscan_right=16
|
||||||
|
#overscan_top=16
|
||||||
|
#overscan_bottom=16
|
||||||
|
|
||||||
|
# uncomment to force a console size. By default it will be display's size minus
|
||||||
|
# overscan.
|
||||||
|
#framebuffer_width=1280
|
||||||
|
#framebuffer_height=720
|
||||||
|
|
||||||
|
# uncomment if hdmi display is not detected and composite is being output
|
||||||
|
hdmi_force_hotplug=1
|
||||||
|
|
||||||
|
# uncomment to force a specific HDMI mode (this will force VGA)
|
||||||
|
#hdmi_group=1
|
||||||
|
#hdmi_mode=1
|
||||||
|
|
||||||
|
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
||||||
|
# DMT (computer monitor) modes
|
||||||
|
#hdmi_drive=2
|
||||||
|
|
||||||
|
# uncomment to increase signal to HDMI, if you have interference, blanking, or
|
||||||
|
# no display
|
||||||
|
#config_hdmi_boost=4
|
||||||
|
|
||||||
|
# uncomment for composite PAL
|
||||||
|
#sdtv_mode=2
|
||||||
|
|
||||||
|
#uncomment to overclock the arm. 700 MHz is the default.
|
||||||
|
#arm_freq=800
|
||||||
|
|
||||||
|
# Uncomment some or all of these to enable the optional hardware interfaces
|
||||||
|
dtparam=i2c_arm=on
|
||||||
|
#dtparam=i2s=on
|
||||||
|
dtparam=spi=on
|
||||||
|
enable_uart=1
|
||||||
|
# Uncomment this to enable the lirc-rpi module
|
||||||
|
#dtoverlay=lirc-rpi
|
||||||
|
|
||||||
|
# Additional overlays and parameters are documented /boot/overlays/README
|
||||||
|
|
||||||
|
# Enable audio (loads snd_bcm2835)
|
||||||
|
dtparam=audio=on
|
||||||
|
dtoverlay=tft35a
|
||||||
|
dtoverlay=ads7846,cs=1,penirq=17,penirq_pull=2,speed=1000000,keep_vref_on=1,swapxy=1,pmax=255,xohms=60,xmin=200,xmax=3900,ymin=200,ymax=3900
|
||||||
63
boot/config-397.txt
Normal file
63
boot/config-397.txt
Normal file
|
|
@ -0,0 +1,63 @@
|
||||||
|
# For more options and information see
|
||||||
|
# http://www.raspberrypi.org/documentation/configuration/config-txt.md
|
||||||
|
# Some settings may impact device functionality. See link above for details
|
||||||
|
|
||||||
|
# uncomment if you get no picture on HDMI for a default "safe" mode
|
||||||
|
#hdmi_safe=1
|
||||||
|
|
||||||
|
# uncomment this if your display has a black border of unused pixels visible
|
||||||
|
# and your display can output without overscan
|
||||||
|
#disable_overscan=1
|
||||||
|
|
||||||
|
# uncomment the following to adjust overscan. Use positive numbers if console
|
||||||
|
# goes off screen, and negative if there is too much border
|
||||||
|
#overscan_left=16
|
||||||
|
#overscan_right=16
|
||||||
|
#overscan_top=16
|
||||||
|
#overscan_bottom=16
|
||||||
|
|
||||||
|
# uncomment to force a console size. By default it will be display's size minus
|
||||||
|
# overscan.
|
||||||
|
#framebuffer_width=1280
|
||||||
|
#framebuffer_height=720
|
||||||
|
|
||||||
|
# uncomment if hdmi display is not detected and composite is being output
|
||||||
|
hdmi_force_hotplug=1
|
||||||
|
|
||||||
|
# uncomment to force a specific HDMI mode (this will force VGA)
|
||||||
|
#hdmi_group=1
|
||||||
|
#hdmi_mode=1
|
||||||
|
|
||||||
|
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
||||||
|
# DMT (computer monitor) modes
|
||||||
|
#hdmi_drive=2
|
||||||
|
|
||||||
|
# uncomment to increase signal to HDMI, if you have interference, blanking, or
|
||||||
|
# no display
|
||||||
|
#config_hdmi_boost=4
|
||||||
|
|
||||||
|
# uncomment for composite PAL
|
||||||
|
#sdtv_mode=2
|
||||||
|
|
||||||
|
#uncomment to overclock the arm. 700 MHz is the default.
|
||||||
|
#arm_freq=800
|
||||||
|
|
||||||
|
# Uncomment some or all of these to enable the optional hardware interfaces
|
||||||
|
dtparam=i2c_arm=on
|
||||||
|
#dtparam=i2s=on
|
||||||
|
dtparam=spi=on
|
||||||
|
enable_uart=1
|
||||||
|
# Uncomment this to enable the lirc-rpi module
|
||||||
|
#dtoverlay=lirc-rpi
|
||||||
|
|
||||||
|
# Additional overlays and parameters are documented /boot/overlays/README
|
||||||
|
|
||||||
|
# Enable audio (loads snd_bcm2835)
|
||||||
|
dtparam=audio=on
|
||||||
|
display_rotate=3
|
||||||
|
max_usb_current=1
|
||||||
|
hdmi_group=2
|
||||||
|
hdmi_mode=1
|
||||||
|
hdmi_mode=87
|
||||||
|
hdmi_cvt 480 800 60 6 0 0 0
|
||||||
|
dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900
|
||||||
63
boot/config-43.txt
Normal file
63
boot/config-43.txt
Normal file
|
|
@ -0,0 +1,63 @@
|
||||||
|
# For more options and information see
|
||||||
|
# http://www.raspberrypi.org/documentation/configuration/config-txt.md
|
||||||
|
# Some settings may impact device functionality. See link above for details
|
||||||
|
|
||||||
|
# uncomment if you get no picture on HDMI for a default "safe" mode
|
||||||
|
#hdmi_safe=1
|
||||||
|
|
||||||
|
# uncomment this if your display has a black border of unused pixels visible
|
||||||
|
# and your display can output without overscan
|
||||||
|
#disable_overscan=1
|
||||||
|
|
||||||
|
# uncomment the following to adjust overscan. Use positive numbers if console
|
||||||
|
# goes off screen, and negative if there is too much border
|
||||||
|
#overscan_left=16
|
||||||
|
#overscan_right=16
|
||||||
|
#overscan_top=16
|
||||||
|
#overscan_bottom=16
|
||||||
|
|
||||||
|
# uncomment to force a console size. By default it will be display's size minus
|
||||||
|
# overscan.
|
||||||
|
#framebuffer_width=1280
|
||||||
|
#framebuffer_height=720
|
||||||
|
|
||||||
|
# uncomment if hdmi display is not detected and composite is being output
|
||||||
|
hdmi_force_hotplug=1
|
||||||
|
|
||||||
|
# uncomment to force a specific HDMI mode (this will force VGA)
|
||||||
|
#hdmi_group=1
|
||||||
|
#hdmi_mode=1
|
||||||
|
|
||||||
|
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
||||||
|
# DMT (computer monitor) modes
|
||||||
|
#hdmi_drive=2
|
||||||
|
|
||||||
|
# uncomment to increase signal to HDMI, if you have interference, blanking, or
|
||||||
|
# no display
|
||||||
|
#config_hdmi_boost=4
|
||||||
|
|
||||||
|
# uncomment for composite PAL
|
||||||
|
#sdtv_mode=2
|
||||||
|
|
||||||
|
#uncomment to overclock the arm. 700 MHz is the default.
|
||||||
|
#arm_freq=800
|
||||||
|
|
||||||
|
# Uncomment some or all of these to enable the optional hardware interfaces
|
||||||
|
dtparam=i2c_arm=on
|
||||||
|
#dtparam=i2s=on
|
||||||
|
dtparam=spi=on
|
||||||
|
enable_uart=1
|
||||||
|
# Uncomment this to enable the lirc-rpi module
|
||||||
|
#dtoverlay=lirc-rpi
|
||||||
|
|
||||||
|
# Additional overlays and parameters are documented /boot/overlays/README
|
||||||
|
|
||||||
|
# Enable audio (loads snd_bcm2835)
|
||||||
|
dtparam=audio=on
|
||||||
|
max_usb_current=1
|
||||||
|
display_rotate=0
|
||||||
|
max_usb_current=1
|
||||||
|
hdmi_group=2
|
||||||
|
hdmi_mode=87
|
||||||
|
hdmi_timings=480 0 1 41 2 272 0 2 10 2 0 0 0 60 0 9000000 3
|
||||||
|
dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900
|
||||||
62
boot/config-5.txt
Normal file
62
boot/config-5.txt
Normal file
|
|
@ -0,0 +1,62 @@
|
||||||
|
# For more options and information see
|
||||||
|
# http://www.raspberrypi.org/documentation/configuration/config-txt.md
|
||||||
|
# Some settings may impact device functionality. See link above for details
|
||||||
|
|
||||||
|
# uncomment if you get no picture on HDMI for a default "safe" mode
|
||||||
|
#hdmi_safe=1
|
||||||
|
|
||||||
|
# uncomment this if your display has a black border of unused pixels visible
|
||||||
|
# and your display can output without overscan
|
||||||
|
#disable_overscan=1
|
||||||
|
|
||||||
|
# uncomment the following to adjust overscan. Use positive numbers if console
|
||||||
|
# goes off screen, and negative if there is too much border
|
||||||
|
#overscan_left=16
|
||||||
|
#overscan_right=16
|
||||||
|
#overscan_top=16
|
||||||
|
#overscan_bottom=16
|
||||||
|
|
||||||
|
# uncomment to force a console size. By default it will be display's size minus
|
||||||
|
# overscan.
|
||||||
|
#framebuffer_width=1280
|
||||||
|
#framebuffer_height=720
|
||||||
|
|
||||||
|
# uncomment if hdmi display is not detected and composite is being output
|
||||||
|
hdmi_force_hotplug=1
|
||||||
|
|
||||||
|
# uncomment to force a specific HDMI mode (this will force VGA)
|
||||||
|
#hdmi_group=1
|
||||||
|
#hdmi_mode=1
|
||||||
|
|
||||||
|
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
||||||
|
# DMT (computer monitor) modes
|
||||||
|
#hdmi_drive=2
|
||||||
|
|
||||||
|
# uncomment to increase signal to HDMI, if you have interference, blanking, or
|
||||||
|
# no display
|
||||||
|
#config_hdmi_boost=4
|
||||||
|
|
||||||
|
# uncomment for composite PAL
|
||||||
|
#sdtv_mode=2
|
||||||
|
|
||||||
|
#uncomment to overclock the arm. 700 MHz is the default.
|
||||||
|
#arm_freq=800
|
||||||
|
|
||||||
|
# Uncomment some or all of these to enable the optional hardware interfaces
|
||||||
|
dtparam=i2c_arm=on
|
||||||
|
#dtparam=i2s=on
|
||||||
|
dtparam=spi=on
|
||||||
|
enable_uart=1
|
||||||
|
# Uncomment this to enable the lirc-rpi module
|
||||||
|
#dtoverlay=lirc-rpi
|
||||||
|
|
||||||
|
# Additional overlays and parameters are documented /boot/overlays/README
|
||||||
|
|
||||||
|
# Enable audio (loads snd_bcm2835)
|
||||||
|
dtparam=audio=on
|
||||||
|
max_usb_current=1
|
||||||
|
hdmi_group=2
|
||||||
|
hdmi_mode=1
|
||||||
|
hdmi_mode=87
|
||||||
|
hdmi_cvt 800 480 60 6 0 0 0
|
||||||
|
dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900
|
||||||
62
boot/config-7B-800x480.txt
Normal file
62
boot/config-7B-800x480.txt
Normal file
|
|
@ -0,0 +1,62 @@
|
||||||
|
# For more options and information see
|
||||||
|
# http://www.raspberrypi.org/documentation/configuration/config-txt.md
|
||||||
|
# Some settings may impact device functionality. See link above for details
|
||||||
|
|
||||||
|
# uncomment if you get no picture on HDMI for a default "safe" mode
|
||||||
|
#hdmi_safe=1
|
||||||
|
|
||||||
|
# uncomment this if your display has a black border of unused pixels visible
|
||||||
|
# and your display can output without overscan
|
||||||
|
#disable_overscan=1
|
||||||
|
|
||||||
|
# uncomment the following to adjust overscan. Use positive numbers if console
|
||||||
|
# goes off screen, and negative if there is too much border
|
||||||
|
#overscan_left=16
|
||||||
|
#overscan_right=16
|
||||||
|
#overscan_top=16
|
||||||
|
#overscan_bottom=16
|
||||||
|
|
||||||
|
# uncomment to force a console size. By default it will be display's size minus
|
||||||
|
# overscan.
|
||||||
|
#framebuffer_width=1280
|
||||||
|
#framebuffer_height=720
|
||||||
|
|
||||||
|
# uncomment if hdmi display is not detected and composite is being output
|
||||||
|
hdmi_force_hotplug=1
|
||||||
|
|
||||||
|
# uncomment to force a specific HDMI mode (this will force VGA)
|
||||||
|
#hdmi_group=1
|
||||||
|
#hdmi_mode=1
|
||||||
|
|
||||||
|
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
||||||
|
# DMT (computer monitor) modes
|
||||||
|
#hdmi_drive=2
|
||||||
|
|
||||||
|
# uncomment to increase signal to HDMI, if you have interference, blanking, or
|
||||||
|
# no display
|
||||||
|
#config_hdmi_boost=4
|
||||||
|
|
||||||
|
# uncomment for composite PAL
|
||||||
|
#sdtv_mode=2
|
||||||
|
|
||||||
|
#uncomment to overclock the arm. 700 MHz is the default.
|
||||||
|
#arm_freq=800
|
||||||
|
|
||||||
|
# Uncomment some or all of these to enable the optional hardware interfaces
|
||||||
|
dtparam=i2c_arm=on
|
||||||
|
#dtparam=i2s=on
|
||||||
|
dtparam=spi=on
|
||||||
|
enable_uart=1
|
||||||
|
# Uncomment this to enable the lirc-rpi module
|
||||||
|
#dtoverlay=lirc-rpi
|
||||||
|
|
||||||
|
# Additional overlays and parameters are documented /boot/overlays/README
|
||||||
|
|
||||||
|
# Enable audio (loads snd_bcm2835)
|
||||||
|
dtparam=audio=on
|
||||||
|
max_usb_current=1
|
||||||
|
hdmi_group=2
|
||||||
|
hdmi_mode=1
|
||||||
|
hdmi_mode=87
|
||||||
|
hdmi_cvt 800 480 60 6 0 0 0
|
||||||
|
dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900
|
||||||
62
boot/config-7C-1024x600.txt
Normal file
62
boot/config-7C-1024x600.txt
Normal file
|
|
@ -0,0 +1,62 @@
|
||||||
|
# For more options and information see
|
||||||
|
# http://www.raspberrypi.org/documentation/configuration/config-txt.md
|
||||||
|
# Some settings may impact device functionality. See link above for details
|
||||||
|
|
||||||
|
# uncomment if you get no picture on HDMI for a default "safe" mode
|
||||||
|
#hdmi_safe=1
|
||||||
|
|
||||||
|
# uncomment this if your display has a black border of unused pixels visible
|
||||||
|
# and your display can output without overscan
|
||||||
|
#disable_overscan=1
|
||||||
|
|
||||||
|
# uncomment the following to adjust overscan. Use positive numbers if console
|
||||||
|
# goes off screen, and negative if there is too much border
|
||||||
|
#overscan_left=16
|
||||||
|
#overscan_right=16
|
||||||
|
#overscan_top=16
|
||||||
|
#overscan_bottom=16
|
||||||
|
|
||||||
|
# uncomment to force a console size. By default it will be display's size minus
|
||||||
|
# overscan.
|
||||||
|
#framebuffer_width=1280
|
||||||
|
#framebuffer_height=720
|
||||||
|
|
||||||
|
# uncomment if hdmi display is not detected and composite is being output
|
||||||
|
hdmi_force_hotplug=1
|
||||||
|
|
||||||
|
# uncomment to force a specific HDMI mode (this will force VGA)
|
||||||
|
#hdmi_group=1
|
||||||
|
#hdmi_mode=1
|
||||||
|
|
||||||
|
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
||||||
|
# DMT (computer monitor) modes
|
||||||
|
#hdmi_drive=2
|
||||||
|
|
||||||
|
# uncomment to increase signal to HDMI, if you have interference, blanking, or
|
||||||
|
# no display
|
||||||
|
#config_hdmi_boost=4
|
||||||
|
|
||||||
|
# uncomment for composite PAL
|
||||||
|
#sdtv_mode=2
|
||||||
|
|
||||||
|
#uncomment to overclock the arm. 700 MHz is the default.
|
||||||
|
#arm_freq=800
|
||||||
|
|
||||||
|
# Uncomment some or all of these to enable the optional hardware interfaces
|
||||||
|
dtparam=i2c_arm=on
|
||||||
|
#dtparam=i2s=on
|
||||||
|
dtparam=spi=on
|
||||||
|
enable_uart=1
|
||||||
|
# Uncomment this to enable the lirc-rpi module
|
||||||
|
#dtoverlay=lirc-rpi
|
||||||
|
|
||||||
|
# Additional overlays and parameters are documented /boot/overlays/README
|
||||||
|
|
||||||
|
# Enable audio (loads snd_bcm2835)
|
||||||
|
dtparam=audio=on
|
||||||
|
max_usb_current=1
|
||||||
|
hdmi_group=2
|
||||||
|
hdmi_mode=1
|
||||||
|
hdmi_mode=87
|
||||||
|
hdmi_cvt 1024 600 60 6 0 0 0
|
||||||
|
dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900
|
||||||
56
boot/config-nomal.txt
Normal file
56
boot/config-nomal.txt
Normal file
|
|
@ -0,0 +1,56 @@
|
||||||
|
# For more options and information see
|
||||||
|
# http://www.raspberrypi.org/documentation/configuration/config-txt.md
|
||||||
|
# Some settings may impact device functionality. See link above for details
|
||||||
|
|
||||||
|
# uncomment if you get no picture on HDMI for a default "safe" mode
|
||||||
|
#hdmi_safe=1
|
||||||
|
|
||||||
|
# uncomment this if your display has a black border of unused pixels visible
|
||||||
|
# and your display can output without overscan
|
||||||
|
#disable_overscan=1
|
||||||
|
|
||||||
|
# uncomment the following to adjust overscan. Use positive numbers if console
|
||||||
|
# goes off screen, and negative if there is too much border
|
||||||
|
#overscan_left=16
|
||||||
|
#overscan_right=16
|
||||||
|
#overscan_top=16
|
||||||
|
#overscan_bottom=16
|
||||||
|
|
||||||
|
# uncomment to force a console size. By default it will be display's size minus
|
||||||
|
# overscan.
|
||||||
|
#framebuffer_width=1280
|
||||||
|
#framebuffer_height=720
|
||||||
|
|
||||||
|
# uncomment if hdmi display is not detected and composite is being output
|
||||||
|
hdmi_force_hotplug=1
|
||||||
|
|
||||||
|
# uncomment to force a specific HDMI mode (this will force VGA)
|
||||||
|
#hdmi_group=1
|
||||||
|
#hdmi_mode=1
|
||||||
|
|
||||||
|
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
||||||
|
# DMT (computer monitor) modes
|
||||||
|
#hdmi_drive=2
|
||||||
|
|
||||||
|
# uncomment to increase signal to HDMI, if you have interference, blanking, or
|
||||||
|
# no display
|
||||||
|
#config_hdmi_boost=4
|
||||||
|
|
||||||
|
# uncomment for composite PAL
|
||||||
|
#sdtv_mode=2
|
||||||
|
|
||||||
|
#uncomment to overclock the arm. 700 MHz is the default.
|
||||||
|
#arm_freq=800
|
||||||
|
|
||||||
|
# Uncomment some or all of these to enable the optional hardware interfaces
|
||||||
|
dtparam=i2c_arm=on
|
||||||
|
#dtparam=i2s=on
|
||||||
|
dtparam=spi=on
|
||||||
|
enable_uart=1
|
||||||
|
# Uncomment this to enable the lirc-rpi module
|
||||||
|
#dtoverlay=lirc-rpi
|
||||||
|
|
||||||
|
# Additional overlays and parameters are documented /boot/overlays/README
|
||||||
|
|
||||||
|
# Enable audio (loads snd_bcm2835)
|
||||||
|
dtparam=audio=on
|
||||||
0
lcd.c
Normal file
0
lcd.c
Normal file
6
usr/99-calibration.conf-28
Normal file
6
usr/99-calibration.conf-28
Normal file
|
|
@ -0,0 +1,6 @@
|
||||||
|
Section "InputClass"
|
||||||
|
Identifier "calibration"
|
||||||
|
MatchProduct "ADS7846 Touchscreen"
|
||||||
|
Option "Calibration" "3770 171 239 3892"
|
||||||
|
Option "SwapAxes" "1"
|
||||||
|
EndSection
|
||||||
6
usr/99-calibration.conf-32
Normal file
6
usr/99-calibration.conf-32
Normal file
|
|
@ -0,0 +1,6 @@
|
||||||
|
Section "InputClass"
|
||||||
|
Identifier "calibration"
|
||||||
|
MatchProduct "ADS7846 Touchscreen"
|
||||||
|
Option "Calibration" "115 3700 3865 155"
|
||||||
|
Option "SwapAxes" "1"
|
||||||
|
EndSection
|
||||||
6
usr/99-calibration.conf-35
Normal file
6
usr/99-calibration.conf-35
Normal file
|
|
@ -0,0 +1,6 @@
|
||||||
|
Section "InputClass"
|
||||||
|
Identifier "calibration"
|
||||||
|
MatchProduct "ADS7846 Touchscreen"
|
||||||
|
Option "Calibration" "3936 227 268 3880"
|
||||||
|
Option "SwapAxes" "1"
|
||||||
|
EndSection
|
||||||
6
usr/99-calibration.conf-397
Normal file
6
usr/99-calibration.conf-397
Normal file
|
|
@ -0,0 +1,6 @@
|
||||||
|
Section "InputClass"
|
||||||
|
Identifier "calibration"
|
||||||
|
MatchProduct "ADS7846 Touchscreen"
|
||||||
|
Option "Calibration" "3865 158 289 3873"
|
||||||
|
Option "SwapAxes" "1"
|
||||||
|
EndSection
|
||||||
6
usr/99-calibration.conf-43
Normal file
6
usr/99-calibration.conf-43
Normal file
|
|
@ -0,0 +1,6 @@
|
||||||
|
Section "InputClass"
|
||||||
|
Identifier "calibration"
|
||||||
|
MatchProduct "ADS7846 Touchscreen"
|
||||||
|
Option "Calibration" "535 3860 254 3883"
|
||||||
|
Option "SwapAxes" "0"
|
||||||
|
EndSection
|
||||||
6
usr/99-calibration.conf-5
Normal file
6
usr/99-calibration.conf-5
Normal file
|
|
@ -0,0 +1,6 @@
|
||||||
|
Section "InputClass"
|
||||||
|
Identifier "calibration"
|
||||||
|
MatchProduct "ADS7846 Touchscreen"
|
||||||
|
Option "Calibration" "140 3951 261 3998"
|
||||||
|
Option "SwapAxes" "0"
|
||||||
|
EndSection
|
||||||
16
usr/99-fbturbo.conf
Normal file
16
usr/99-fbturbo.conf
Normal file
|
|
@ -0,0 +1,16 @@
|
||||||
|
# This is a minimal sample config file, which can be copied to
|
||||||
|
# /etc/X11/xorg.conf in order to make the Xorg server pick up
|
||||||
|
# and load xf86-video-fbturbo driver installed in the system.
|
||||||
|
#
|
||||||
|
# When troubleshooting, check /var/log/Xorg.0.log for the debugging
|
||||||
|
# output and error messages.
|
||||||
|
# Run "man fbturbo" to get additional information about the extra
|
||||||
|
# configuration options for tuning the driver.
|
||||||
|
|
||||||
|
Section "Device"
|
||||||
|
Identifier "Allwinner A10/A13/A20 FBDEV"
|
||||||
|
Driver "fbturbo"
|
||||||
|
Option "fbdev" "/dev/fb1"
|
||||||
|
|
||||||
|
Option "SwapbuffersWait" "true"
|
||||||
|
EndSection
|
||||||
16
usr/99-fbturbo.conf-HDMI
Normal file
16
usr/99-fbturbo.conf-HDMI
Normal file
|
|
@ -0,0 +1,16 @@
|
||||||
|
# This is a minimal sample config file, which can be copied to
|
||||||
|
# /etc/X11/xorg.conf in order to make the Xorg server pick up
|
||||||
|
# and load xf86-video-fbturbo driver installed in the system.
|
||||||
|
#
|
||||||
|
# When troubleshooting, check /var/log/Xorg.0.log for the debugging
|
||||||
|
# output and error messages.
|
||||||
|
# Run "man fbturbo" to get additional information about the extra
|
||||||
|
# configuration options for tuning the driver.
|
||||||
|
|
||||||
|
Section "Device"
|
||||||
|
Identifier "Allwinner A10/A13/A20 FBDEV"
|
||||||
|
Driver "fbturbo"
|
||||||
|
Option "fbdev" "/dev/fb0"
|
||||||
|
|
||||||
|
Option "SwapbuffersWait" "true"
|
||||||
|
EndSection
|
||||||
1
usr/cmdline.txt
Normal file
1
usr/cmdline.txt
Normal file
|
|
@ -0,0 +1 @@
|
||||||
|
dwc_otg.lpm_enable=0 console=tty1 console=ttyAMA0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline rootwait fbcon=map:10 fbcon=font:ProFont6x11 logo.nologo
|
||||||
72
usr/inittab
Normal file
72
usr/inittab
Normal file
|
|
@ -0,0 +1,72 @@
|
||||||
|
# /etc/inittab: init(8) configuration.
|
||||||
|
# $Id: inittab,v 1.91 2002/01/25 13:35:21 miquels Exp $
|
||||||
|
|
||||||
|
# The default runlevel.
|
||||||
|
id:2:initdefault:
|
||||||
|
|
||||||
|
# Boot-time system configuration/initialization script.
|
||||||
|
# This is run first except when booting in emergency (-b) mode.
|
||||||
|
si::sysinit:/etc/init.d/rcS
|
||||||
|
|
||||||
|
# What to do in single-user mode.
|
||||||
|
~~:S:wait:/sbin/sulogin
|
||||||
|
|
||||||
|
# /etc/init.d executes the S and K scripts upon change
|
||||||
|
# of runlevel.
|
||||||
|
#
|
||||||
|
# Runlevel 0 is halt.
|
||||||
|
# Runlevel 1 is single-user.
|
||||||
|
# Runlevels 2-5 are multi-user.
|
||||||
|
# Runlevel 6 is reboot.
|
||||||
|
|
||||||
|
l0:0:wait:/etc/init.d/rc 0
|
||||||
|
l1:1:wait:/etc/init.d/rc 1
|
||||||
|
l2:2:wait:/etc/init.d/rc 2
|
||||||
|
l3:3:wait:/etc/init.d/rc 3
|
||||||
|
l4:4:wait:/etc/init.d/rc 4
|
||||||
|
l5:5:wait:/etc/init.d/rc 5
|
||||||
|
l6:6:wait:/etc/init.d/rc 6
|
||||||
|
# Normally not reached, but fallthrough in case of emergency.
|
||||||
|
z6:6:respawn:/sbin/sulogin
|
||||||
|
|
||||||
|
# What to do when CTRL-ALT-DEL is pressed.
|
||||||
|
ca:12345:ctrlaltdel:/sbin/shutdown -t1 -a -r now
|
||||||
|
|
||||||
|
# Action on special keypress (ALT-UpArrow).
|
||||||
|
#kb::kbrequest:/bin/echo "Keyboard Request--edit /etc/inittab to let this work."
|
||||||
|
|
||||||
|
# What to do when the power fails/returns.
|
||||||
|
pf::powerwait:/etc/init.d/powerfail start
|
||||||
|
pn::powerfailnow:/etc/init.d/powerfail now
|
||||||
|
po::powerokwait:/etc/init.d/powerfail stop
|
||||||
|
|
||||||
|
# /sbin/getty invocations for the runlevels.
|
||||||
|
#
|
||||||
|
# The "id" field MUST be the same as the last
|
||||||
|
# characters of the device (after "tty").
|
||||||
|
#
|
||||||
|
# Format:
|
||||||
|
# <id>:<runlevels>:<action>:<process>
|
||||||
|
#
|
||||||
|
# Note that on most Debian systems tty7 is used by the X Window System,
|
||||||
|
# so if you want to add more getty's go ahead but skip tty7 if you run X.
|
||||||
|
#
|
||||||
|
1:2345:respawn:/sbin/getty --noclear 38400 tty1
|
||||||
|
2:23:respawn:/sbin/getty 38400 tty2
|
||||||
|
3:23:respawn:/sbin/getty 38400 tty3
|
||||||
|
4:23:respawn:/sbin/getty 38400 tty4
|
||||||
|
5:23:respawn:/sbin/getty 38400 tty5
|
||||||
|
6:23:respawn:/sbin/getty 38400 tty6
|
||||||
|
|
||||||
|
# Example how to put a getty on a serial line (for a terminal)
|
||||||
|
#
|
||||||
|
#T0:23:respawn:/sbin/getty -L ttyS0 9600 vt100
|
||||||
|
#T1:23:respawn:/sbin/getty -L ttyS1 9600 vt100
|
||||||
|
|
||||||
|
# Example how to put a getty on a modem line.
|
||||||
|
#
|
||||||
|
#T3:23:respawn:/sbin/mgetty -x0 -s 57600 ttyS3
|
||||||
|
|
||||||
|
|
||||||
|
#Spawn a getty on Raspberry Pi serial line
|
||||||
|
T0:23:respawn:/sbin/getty -L ttyAMA0 115200 vt100
|
||||||
13
usr/modules-HDMI
Normal file
13
usr/modules-HDMI
Normal file
|
|
@ -0,0 +1,13 @@
|
||||||
|
# /etc/modules: kernel modules to load at boot time.
|
||||||
|
#
|
||||||
|
# This file contains the names of kernel modules that should be loaded
|
||||||
|
# at boot time, one per line. Lines beginning with "#" are ignored.
|
||||||
|
# Parameters can be specified after the module name.
|
||||||
|
|
||||||
|
snd-bcm2835
|
||||||
|
i2c-bcm2708
|
||||||
|
i2c-dev
|
||||||
|
|
||||||
|
#flexfb width=320 height=480 regwidth=16 init=-1,0xb0,0x0,-1,0x11,-2,250,-1,0x3A,0x55,-1,0xC2,0x44,-1,0xC5,0x00,0x00,0x00,0x00,-1,0xE0,0x0F,0x1F,0x1C,0x0C,0x0F,0x08,0x48,0x98,0x37,0x0A,0x13,0x04,0x11,0x0D,0x00,-1,0xE1,0x0F,0x32,0x2E,0x0B,0x0D,0x05,0x47,0x75,0x37,0x06,0x10,0x03,0x24,0x20,0x00,-1,0xE2,0x0F,0x32,0x2E,0x0B,0x0D,0x05,0x47,0x75,0x37,0x06,0x10,0x03,0x24,0x20,0x00,-1,0x36,0x28,-1,0x11,-1,0x29,-3
|
||||||
|
#fbtft_device debug=3 rotate=90 name=flexfb speed=16000000 gpios=reset:25,dc:24
|
||||||
|
#ads7846_device model=7846 cs=1 gpio_pendown=17 keep_vref_on=1 swap_xy=1 pressure_max=255 x_plate_ohms=60 x_min=200 x_max=3900 y_min=200 y_max=3900
|
||||||
BIN
usr/tft35a-overlay.dtb
Normal file
BIN
usr/tft35a-overlay.dtb
Normal file
Binary file not shown.
BIN
usr/tft9341-overlay.dtb
Normal file
BIN
usr/tft9341-overlay.dtb
Normal file
Binary file not shown.
BIN
xinput-calibrator_0.7.5-1_armhf.deb
Normal file
BIN
xinput-calibrator_0.7.5-1_armhf.deb
Normal file
Binary file not shown.
Loading…
Reference in a new issue